Found 8165 leads.   Views from 10 to 20
 
in Secondary Jaw Crusher
MARSMAN : Secondary Jaw Crushers are ideally suited for crushing of hard granite stone, black tarp rock, river gravel, lime stone, coal, iron, ore etc. BODY : The body is made form tested M.S. Plates. It is fabricated with horizontal and vertical ribs for strength and sturdiness, the body is annealed & stress released by heat treatment process to reduce the chance of the body getting cracked. SWINGING LEVER : The swinging lever (pitman) is fabricated out of M.S. Plates with high tensile strength and it is annealed by heat treatment process and then it is precision machined for smooth crushing stroke. TOGGLE PLATES & TOGGLE BEARINGS : For equal balance and load distribution the crank shaft is centrally fitted on cast steel toggle bearings. The cast steel toggle bearings withstand excessive wear & tear and convey correct crushing stroke. JAW PLATES & SIDE PLATES : The jaw plates are made of high tensil manganese steel. Specially designed teeth of Jaw plates are suitable to produce cubical shape material as per required output sizes. One jaw is fixed and the other jaw is fitted on swinging lever. He side plates are of close fitting type which prevent any wear to the body, which is made out of high grade manganese steel. CRANK SHAFT & BEARING : The crank shaft is made of forged steel and fitted in heavy duty spherical double roller bearings which ensures smooth operation. The bearings are fitted on both sides of the crank shaft and two in swinging lever, which are well sealed against possible entry o dust and moisture by labyrinth seals. For lubrications grease nipples are fitted at appropriate places. FLYWHEELS : Heavy duty cast iron flywheels are fitted on both the ends of crank shaft. These flywheels are machined all over, counter weight fitted and balance to ensure steady crushing force. WARRANTY : MARSMAN Jaw Crushers are warranted for ONE YEAR against manufacturing defects. However, the warranty does not cover breakdowns under normal wear & tear due to misuse / mistake made by operator.
Contact Info:  Registered users can see this address Registered users can see this phone number Registered users can see this facsimile number Registered users can see email addresses Registered users can see this www address
  • Currently ranking is 0.
  • 1
  • 2
  • 3
  • 4
  • 5

 

image
cn lead-free reflow soldering
ETA E10 Lead free hot air reflow oven Heating System > Ten groups of top and bottom forced hot air convection heating zones. > Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air convection. > Independent temperature control in each zone to ensure temperature uniformity within the process tunnel. > Power consumption savings of 1/3 as compared to other systems. > Patented motorized blower in each zone is designed to ensure stable air pressure, withstand high process temperature and is disturbance-free. > Audible and light tower alarm for temperature limits, PCB drop, PCB jam and blower malfunction. > Fast start-up (within 20 minutes) from room temperature to work temperature due to the high efficiency of the motorized heating plates. Cooling System > Two (2) groups of forced air convection cooling zones. Distortion-free Conveyor System with Automated Chain Lubrication > Combined pin chain rail and mesh belt conveyor system (Note: Mesh belt is not available on machines with center board support.) > Closed-loop computer control of the conveyor provides a precise and repeatable reflow process. > Automated chain lubrication system with a computer controlled central reservoir. Lubricant is added directly to the conveyor brush eliminating operator interface for this maintenance. Fresh Air Recharge System > Fresh air is supplied to each zone uniformly to provide a rapid process transfer. Flux Management System > Air amplifier forces supercharged flux collection and recirculation. > Flux exhaust chimney with drawer shaped filter net is easy to access for maintenance. Control System > PC control system with windows based control software. Additional Features > Integrated UPS will be automatically activated in case of main power failure and will keep control PC and conveyor running for minimum 8 minutes to send out PCBs inside the oven tunnel. > Motorized hood lift allows easy access to the inside of the oven for service and maintenance. > Five (5) profiling ports and integrated profiling software are designed for convenient temperature profiling. > Swing arm control PC station > Four (4) emergency stop switches > Two (2) exhaust ports > SMEMA interface > System documentation Specifications : E10(10-Zone) General Outside Dimension(L*W*H) : 6100x1350x1490mm Standard Color : Computer Grey Weight : Approx.2350KG Number Of Heating Zones : Up10/Bottom10 Length Of Heating Zones : 3200mm Exhaust Volume : 10M3/minx2(通) Exhausts Standard Feature Of Control System Electric Supply Required : 3phase,380V 50/60Hz Power For Warm : Up35KW Power Consumption : 12KW Warming Time : Approx.20 minute Temp. Setting Range : Room Temp. --- 300℃ Temperature Control Method : PID Close Loop Control + SSR Driving Temperature Control Precision : ± 1.0℃ Temperature Deviation on PCB : ± 1.5℃ (by MR Board Test Standard) Heating Element : Especial Heating elements For Long Life ; Commutated Element : Aluminium Alloy Plate Max. Temp. Gap Between Preheat & Reflow Setting : 80℃ Max. Temp. Gap Between Preheat Zones Setting : 40℃ Max. Temp. Gap Between Reflow Zones Setting : 50℃ Data Storage : Process Data and Status Storage Abnormal Alarm : Abnormal Temperature (Extra-high / Extra-low Temp.) Board Dropped Alarm : Tower Light: Yellow–Warming; Green-Normal; Red-Abnormal Features Of Conveyor System Rail Number : 1 Lane Max.Width Of PCB : 320mm (Option:610mm ) Components Clearance : Top/ Bottom Clearance of PCB is 25mm Converyor Direction : L→R (Option: R→L) Fixed Rail Side : Front Rail Fixed(Option:Rear Rail Fixed) Transmission Agent : Air-Reflow = Chain + Mesh , N2-Reflow=Chain(Mesh is option) Center Support (Option) : Preventing PCB warp such too wide and heavy component load Converyor Height : 900+/-20mm Converyor Speed Range : 300~2000mm/min Lubrication Auto-Afflux : Standard Temp. Thermocouple Slot : Standard Driven Top Hood Opening : Standard On Line Editing : Standard Cooling Method : Forced-Air (Standard), Water-Chiller (Option) Model for Nitrogen Process Power For Warm : Up40KW Power Consumption : 15KW Flux Management System : Flux Reclaimed and Filtration standard for N2Oven, easy clean-up. N2 containment at Entry and Exit End : Standard Flux Reclaim System : Standard Nitrogen Flow Meter : Standard Oxygen Analyser : Option Nitrogen Consumption [Standard] : 400~1000PPM 20M3/H Water Chiller : 3 HP ; External Stand-alone Type ; Powerful Cooling suit to Lead-Free Process Required Skype:chinasmai,www.etasmt.com ETA Electronic equipment CO.,LTD. to provide professional SMT automatic production line solution,The company specializes in SMT chip mounter(New samsung:SM421,SM411,SM100 etc)(second-hand: CP40L; CP40LV; CP45F; CP45FV; CP45FVneo); YAMAHA SMT machine (YAMAHA Chip shooter); JUKI chip mounter ,SIEMENS SMT machine ,PANASONIC SMT Chip mounter, FUJI second-hand SMT machine.We are also sell printing machine,Point glue machine, Reflow soldering,Wave soldering,Automatic plug-in machines,SAMSUNG SMT machine feida ,Accessories ,stencil printer,Reflow oven,flow welding,Panasert,AOI,X-ray,LED automatic die bonder etc,For communication products manufacturers,LED display, lighting manufacturers; SMT, AI materials processing, and other enterprises provide the required equipment or wiring scheme. Main new SAMSUNG chip mounter:SM421S,SM421,SM411,SM431,SLM100,SLM120,SM471,SM481 etc. YAMAHA SMT machine:YS12,YS24,YS100,YG12,YG100RA,YV100X. SIEMENS SMT shooter:D4,D2,D1,S20 25 27 50 60 ,F3,F4,F5 PANASONIC SMT equipment:CM402,CM602,NPM. JUKI Chip shooter:KE2070,KE2080,KE2060,KE2050. FUJI SMT mounter:CP6,CP642,CP643,CP742,CP842,XP241,QP341,QP242,IP3,IP2. SANYO Automatic Mounter:TCM3000Z,TCM-X200. I PULSE FV5530,7100.M1,M2,M3,M4 MIRAE MPS1010,MX100,MX200 NEW automatic plug-in machines, horizontal plug, Vertical plug,Bulk LED plug,Reflow oven, wave soldering, domestic, import have lead, lead-free reflow soldering; Wave soldering, Other SMT related equipment:: AOI; X - ray testing equipment t; Semi-automatic and fully automatic printing machine.
Contact Info:  Registered users can see this address Registered users can see this phone number Registered users can see this facsimile number Registered users can see email addresses Registered users can see this www address
  • Currently ranking is 0.
  • 1
  • 2
  • 3
  • 4
  • 5

 

image
 
cn Spherical Double Row Full Complement Roller Bearing Floating Type
Spherical double row full complement roller bearing allows relative or line movement between two parts, ourpherical double row full complement roller bearing are made from top quailty steel, they are various in size, base on their carrying capcity and limiting speed SBI Full Complement Cylindrical Roller Bearings (Full Complement Bearings) are designed to carry heavy load. Comparing with traditional bearings with cage, full complement cylindrical bearings have much higher loading capacity. The radial cross section of the type of bearings is very small. So it can be very space – saving. However the limiting speed of the bearings is relatively lower. All the multi – row cylindrical roller bearings are with a lubrication groove and one nipple on the outer ring. A minimal load is required (C/P
Contact Info:  Registered users can see this address Registered users can see this phone number Registered users can see email addresses Registered users can see this www address
  • Currently ranking is 0.
  • 1
  • 2
  • 3
  • 4
  • 5

 

image
cn Multi-stage Row Cylindrical Roller Thrust Bearing Tandem Bearing
SBI Tandem Bearing ( Multi-Stage Cylindrical Roller Thrust Bearings ) type:1.Basic type The components of this Thrust Bearings are demountable. The user should assemble or dismount the bearing meticulously according to numeral order we provide.2. Shaft type It is made by penetrating an axis through the inner bore of basic type multi-stage cylindrical roller thrust bearing and fastening the bearing to the axis by locking collar.The components of this type of cylindrical roller thrust bearing are inseparable.3.Sleeve type The locking collar is made by covering a sleeve to the external of the basic type multi-stage cylindrical roller thrust bearing. It is also inseparable, and is assembled and disassembled as a whole. Method of Code NameFor example:M4CT2264 four-row tandem thrust bearing, interior diameter 22mm, exterior diameter 64mm;M3CT33105 three-row tandem thrust bearing, interior diameter 33mm, exterior diameter 105mm;M8CT120360 eight-row tandem thrust bearing, interior diameter 120mm, exterior diameter 360mm;M5CT2264A1 five-row tandem bearing, interior diameter 22mm, exterior diameter 64mm, (shaft type);M6CT38160A2 six-row tandem bearing, interior diameter 38mm, exterior diameter 160mm; (sleeve type) Using Suggestions for and Applications of Tandem Thrust Roller BearingWhile using tandem thrust bearings, users should follow the following rules:1. Preload1% of the dynamic basic load rating should be preloaded. The dynamic basic load rating of every kind of tandem bearing is presented in Figure 1~3. Those not listed in the Figure will be provided by our company. 2. Radial guidanceFull complement cylindrical roller bearings and needle roller bearing can be used. 3. Eliminating titlingThe supporting parts of our thrust bearing must be machined to eliminate tilting. 4. Mounting toleranceTo ensure the normal operation, we recommend the following mounting tolerance: shaft f6 and housing bore F7. 5. Bearing lubricationTandem bearings should be lubricated frequently by thin oil lubrication. 6. Bearing installationWhile assembling and disassembling the bearings, users should not utilize hammer or other heavy things to strike their components
Contact Info:  Registered users can see this address Registered users can see this phone number Registered users can see email addresses Registered users can see this www address
  • Currently ranking is 0.
  • 1
  • 2
  • 3
  • 4
  • 5

 

image
carbon Elbow,,Socket,Bushings Size Elbow
Detailed Product Description Elbow,,Socket,Bushings,galvanized malleable iron pipes Malleable cast Iron pipe fitting 1.Size1/8''-6'' 2.Thread standard:BS, ANSI&DIN 3.Black, hot dipped gal, electro gal Introduction-Manufacturer: 1) Malleable cast iron pipe fitting: a) Products: Elbow, Tee, Socket, Nipples, Bushings, Union, Bends, Cross, etc b) Type: Plain, beaded / beaded with ribs, banded / banded with ribs c) Surface treatment: normal black, galvanized (hot dipped), electrical galvanized; Baked galvanized d) Grades: heavy series, standard series, light series e) Size: 1/8’’-6’’ f) Standards: i) DIN (Germany) standard, DIN 2950/1692/2999 ii) BS (British) standard, ISO49 / ISO5922 / ISO7/1 iii) ANSI standard, ASTM B16.3 B16.14 B16.39 / B1.20.1 2) Malleable casting products: produce according to supplied samples or drawings Material: Blackheart Malleable Cast Iron B350-10 or B300-06 1. Mechanical Properties: Parameter Standard Tensile strength, MPa Min. 300 Elongation, % Min.6 Hardness, HB Max.150 2. Chemical composition of castings ( after decarbonizing glow): Element Content Carbon (C), % 0-2% (dependingon the walls thickness) Silicon (Si), % 0.7-0.9% Manganese (Mn), % 0.2-0.65% Sulphur (S), % Max. 0.2% Phosphor (P), % Max. 0.1%
Contact Info:  Registered users can see this address Registered users can see this phone number Registered users can see this facsimile number Registered users can see email addresses Registered users can see this www address
  • Currently ranking is 0.
  • 1
  • 2
  • 3
  • 4
  • 5

 

image
 
carbon fitting elbow tee
Detailed Product Description malleable iron pipes fitting elbow。tee Malleable cast Iron pipe fitting 1.Size1/8''-6'' 2.Thread standard:BS, ANSI&DIN 3.Black, hot dipped gal, electro gal Introduction-Manufacturer: 1) Malleable cast iron pipe fitting: a) Products: Elbow, Tee, Socket, Nipples, Bushings, Union, Bends, Cross, etc b) Type: Plain, beaded / beaded with ribs, banded / banded with ribs c) Surface treatment: normal black, galvanized (hot dipped), electrical galvanized; Baked galvanized d) Grades: heavy series, standard series, light series e) Size: 1/8’’-6’’ f) Standards: i) DIN (Germany) standard, DIN 2950/1692/2999 ii) BS (British) standard, ISO49 / ISO5922 / ISO7/1 iii) ANSI standard, ASTM B16.3 B16.14 B16.39 / B1.20.1 2) Malleable casting products: produce according to supplied samples or drawings Material: Blackheart Malleable Cast Iron B350-10 or B300-06 1. Mechanical Properties: Parameter Standard Tensile strength, MPa Min. 300 Elongation, % Min.6 Hardness, HB Max.150 2. Chemical composition of castings ( after decarbonizing glow): Element Content Carbon (C), % 0-2% (dependingon the walls thickness) Silicon (Si), % 0.7-0.9% Manganese (Mn), % 0.2-0.65% Sulphur (S), % Max. 0.2% Phosphor (P), % Max. 0.1%
Contact Info:  Registered users can see this address Registered users can see this phone number Registered users can see this facsimile number Registered users can see email addresses Registered users can see this www address
  • Currently ranking is 0.
  • 1
  • 2
  • 3
  • 4
  • 5

 

image
pipe coupling Elbow,,Socket,Bushings, galvanized malleable ironSteel
Detailed Product Description Elbow,,Socket,Bushings,galvanized malleable iron pipes Malleable cast Iron pipe fitting 1.Size1/8''-6'' 2.Thread standard:BS, ANSI&DIN 3.Black, hot dipped gal, electro gal Introduction-Manufacturer: 1) Malleable cast iron pipe fitting: a) Products: Elbow, Tee, Socket, Nipples, Bushings, Union, Bends, Cross, etc b) Type: Plain, beaded / beaded with ribs, banded / banded with ribs c) Surface treatment: normal black, galvanized (hot dipped), electrical galvanized; Baked galvanized d) Grades: heavy series, standard series, light series e) Size: 1/8’’-6’’ f) Standards: i) DIN (Germany) standard, DIN 2950/1692/2999 ii) BS (British) standard, ISO49 / ISO5922 / ISO7/1 iii) ANSI standard, ASTM B16.3 B16.14 B16.39 / B1.20.1 2) Malleable casting products: produce according to supplied samples or drawings Material: Blackheart Malleable Cast Iron B350-10 or B300-06 1. Mechanical Properties: Parameter Standard Tensile strength, MPa Min. 300 Elongation, % Min.6 Hardness, HB Max.150 2. Chemical composition of castings ( after decarbonizing glow): Element Content Carbon (C), % 0-2% (dependingon the walls thickness) Silicon (Si), % 0.7-0.9% Manganese (Mn), % 0.2-0.65% Sulphur (S), % Max. 0.2% Phosphor (P), % Max. 0.1%
Contact Info:  Registered users can see this address Registered users can see this phone number Registered users can see this facsimile number Registered users can see email addresses Registered users can see this www address
  • Currently ranking is 0.
  • 1
  • 2
  • 3
  • 4
  • 5

 

image
malleable iron pipes fitting elbow tee Steel pipe
Detailed Product Description malleable iron pipes fitting elbow。tee Malleable cast Iron pipe fitting 1.Size1/8''-6'' 2.Thread standard:BS, ANSI&DIN 3.Black, hot dipped gal, electro gal Introduction-Manufacturer: 1) Malleable cast iron pipe fitting: a) Products: Elbow, Tee, Socket, Nipples, Bushings, Union, Bends, Cross, etc b) Type: Plain, beaded / beaded with ribs, banded / banded with ribs c) Surface treatment: normal black, galvanized (hot dipped), electrical galvanized; Baked galvanized d) Grades: heavy series, standard series, light series e) Size: 1/8’’-6’’ f) Standards: i) DIN (Germany) standard, DIN 2950/1692/2999 ii) BS (British) standard, ISO49 / ISO5922 / ISO7/1 iii) ANSI standard, ASTM B16.3 B16.14 B16.39 / B1.20.1 2) Malleable casting products: produce according to supplied samples or drawings Material: Blackheart Malleable Cast Iron B350-10 or B300-06 1. Mechanical Properties: Parameter Standard Tensile strength, MPa Min. 300 Elongation, % Min.6 Hardness, HB Max.150 2. Chemical composition of castings ( after decarbonizing glow): Element Content Carbon (C), % 0-2% (dependingon the walls thickness) Silicon (Si), % 0.7-0.9% Manganese (Mn), % 0.2-0.65% Sulphur (S), % Max. 0.2% Phosphor (P), % Max. 0.1%
Contact Info:  Registered users can see this address Registered users can see this phone number Registered users can see this facsimile number Registered users can see email addresses Registered users can see this www address
  • Currently ranking is 0.
  • 1
  • 2
  • 3
  • 4
  • 5

 

image
carbon Manufacturer Galvanized malleable castiron pipes
Detailed Product Description Manufacturer Galvanized malleable cast iron pipe Malleable cast Iron pipe fitting 1.Size1/8''-6'' 2.Thread standard:BS, ANSI&DIN 3.Black, hot dipped gal, electro gal Introduction-Manufacturer: 1) Malleable cast iron pipe fitting: a) Products: Elbow, Tee, Socket, Nipples, Bushings, Union, Bends, Cross, etc b) Type: Plain, beaded / beaded with ribs, banded / banded with ribs c) Surface treatment: normal black, galvanized (hot dipped), electrical galvanized; Baked galvanized d) Grades: heavy series, standard series, light series e) Size: 1/8’’-6’’ f) Standards: i) DIN (Germany) standard, DIN 2950/1692/2999 ii) BS (British) standard, ISO49 / ISO5922 / ISO7/1 iii) ANSI standard, ASTM B16.3 B16.14 B16.39 / B1.20.1 2) Malleable casting products: produce according to supplied samples or drawings Material: Blackheart Malleable Cast Iron B350-10 or B300-06 1. Mechanical Properties: Parameter Standard Tensile strength, MPa Min. 300 Elongation, % Min.6 Hardness, HB Max.150 2. Chemical composition of castings ( after decarbonizing glow): Element Content Carbon (C), % 0-2% (dependingon the walls thickness) Silicon (Si), % 0.7-0.9% Manganese (Mn), % 0.2-0.65% Sulphur (S), % Max. 0.2% Phosphor (P), % Max. 0.1%
Contact Info:  Registered users can see this address Registered users can see this phone number Registered users can see this facsimile number Registered users can see email addresses Registered users can see this www address
  • Currently ranking is 0.
  • 1
  • 2
  • 3
  • 4
  • 5

 

image
carbon Elbow,,Socket,Bushings Size Elbow
Detailed Product Description Elbow,,Socket,Bushings,galvanized malleable iron pipes Malleable cast Iron pipe fitting 1.Size1/8''-6'' 2.Thread standard:BS, ANSI&DIN 3.Black, hot dipped gal, electro gal Introduction-Manufacturer: 1) Malleable cast iron pipe fitting: a) Products: Elbow, Tee, Socket, Nipples, Bushings, Union, Bends, Cross, etc b) Type: Plain, beaded / beaded with ribs, banded / banded with ribs c) Surface treatment: normal black, galvanized (hot dipped), electrical galvanized; Baked galvanized d) Grades: heavy series, standard series, light series e) Size: 1/8’’-6’’ f) Standards: i) DIN (Germany) standard, DIN 2950/1692/2999 ii) BS (British) standard, ISO49 / ISO5922 / ISO7/1 iii) ANSI standard, ASTM B16.3 B16.14 B16.39 / B1.20.1 2) Malleable casting products: produce according to supplied samples or drawings Material: Blackheart Malleable Cast Iron B350-10 or B300-06 1. Mechanical Properties: Parameter Standard Tensile strength, MPa Min. 300 Elongation, % Min.6 Hardness, HB Max.150 2. Chemical composition of castings ( after decarbonizing glow): Element Content Carbon (C), % 0-2% (dependingon the walls thickness) Silicon (Si), % 0.7-0.9% Manganese (Mn), % 0.2-0.65% Sulphur (S), % Max. 0.2% Phosphor (P), % Max. 0.1%
Contact Info:  Registered users can see this address Registered users can see this phone number Registered users can see this facsimile number Registered users can see email addresses Registered users can see this www address
  • Currently ranking is 0.
  • 1
  • 2
  • 3
  • 4
  • 5

 

image
Page 2 of 817